View AQY221N3V_1027449.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

UL
pending
CSA
pending
RF (Radio Frequency) C (by) R 5 SSOP Type FEATURES
4.45 .175 1.80 .071 2.65 .104
PhotoMOS RELAYS
TYPICAL APPLICATIONS
Measuring and testing equipment 1. Test equipment IC tester, Liquid crystal driver tester, semiconductor performance tester 2. Board tester Bear board tester, In-circuit tester, function tester 3. Medical equipment Ultrasonic wave diagnostic machine 4. Multi-point recorder Warping, thermo couple
mm inch
1
4
2
3
1. Reduced package size Lower surface has been reduced 60% and mounting space 40% compared to conventional 4-pin SOP type. 2. Lower output capacitance and onresistance Output capacitance(C): 1.0pF (typ.) ON resistance(R): 5.5 (typ.) 3. Mounting space has been reduced and output signals have been improved by using new flat lead terminals.
Conventional SOP type SSOP
Flat lead
4. High speed switching Turn on time: 0.02ms Turn off time: 0.02ms
TYPES
Circuit arrangement 1 Form A Type AC/DC type Output rating* Load voltage Load current 25 V 150 mA Tape and reel packing style Picked from the 1/4-pin side Picked from the 2/3-pin side AQY221N3VY AQY221N3VW Packing quantity in tape and reel 3,500 pcs.
* Indicate the peak AC and DC values. Notes: (1)Tape package is the standard packing style. (2)For space reasons, the initial letters of the product number "AQY and V", the package type indicator "Y" and "W" are omitted from the seal.
RATING
1. Absolute maximum ratings (Ambient temperature: 25C 77F)
Item LED forward current LED reverse voltage Input Peak forward current Power dissipation Load voltage (peak AC) Continuous load current (peak AC) Output Peak load current Power dissipation Total power dissipation I/O isolation voltage Temperature Operating limits Storage Symbol IF VR IFP Pin VL IL Ipeak Pout PT Viso Topr Tstg AQY221N3V 50mA 5V 1A 75mW 25V 0.15A 0.4A 250mW 300mW 1,500V AC -40C to +85C -40F to +185F -40C to +100C -40F to +212F Remarks
f=100 Hz, Duty factor=0.1%
Peak AC,DC 100 ms (1 shot), VL= DC
Non-condensing at low temperatures
PhotoMOS Relays RF CR5 SSOP ASCT1B268E '03.3
http://www.naisrelay.com/
New
1
AQY221N3V
2. Electrical characteristics (Ambient temperature: 25C 77F)
Item Typical LED operate current Maximum Minimum Input LED turn off current Typical Typical LED dropout voltage Maximum Typical On resistance Maximum Typical Output Output capacitance Maximum Typical Off state leakage current Maximum Typical Turn on time* Maximum Switching speed Typical Transfer characteristics I/O capacitance Maximum Initial I/O isolation resistance Minimum Riso Turn off time* Maximum Typical Ciso 1.5 pF 1,000M Toff 0.2 ms 0.8 pF 0.02ms Ton 0.5ms ILeak 10 nA 0.02 ms Cout 1.5 pF 0.01 nA Ron 7.5 1.0 pF VF 1.5 V 5.5 IF = 5mA IL = 80 mA Within 1 s on time IF = 0 VB = 0 V f = 1 MHz IF = 0 VL = Max. IF = 5mA VL = 10V RL = 125 IF = 5mA VL = 10V RL = 125 f = 1MHz VB = 0 500V DC IFoff 0.9 mA 1.14 V (1.35 V at IF = 50mA) IF = 5mA IFon 3.0 mA 0.2 mA IL = 80 mA Symbol AQY221N3V 1.0 mA IL = 80 mA Condition
Note: Recommendable LED forward current IF = 5 mA. For type of connection, see Page 5. *Turn on/Turn off time
Input
90% 10%
Output
Ton
Toff
REFERENCE DATA
1. Load current vs. ambient temperature characteristics
Allowable ambient temperature: -40C to +85C -40F to +185F
200 200
2. Load current vs. Load voltage characteristics
Ambient temperature: 25C 77F
3. On resistance vs. ambient temperature characteristics
Measured portion: between terminals 3 and 4 LED current: 5 mA; Load voltage: Max. (DC); Load current: 80mA (DC)
25
Load current, mA
Load current, mA
150
150
On resistance, 0 5 10 15 20 25 30
20
15
100
100
10
50
50 5
0 -40
-20
0
20
40
60
8085 100
0
0
-40 -20
0
20
40
60
8085
Ambient temperature, C
Load voltage, V
Ambient temperature, C
2
AQY221N3V
4. Turn on time vs. ambient temperature characteristics
Measured portion: between terminals 3 and 4 LED current: 5 mA; Load voltage: 10V (DC); Continuous load current: 80mA (DC)
0.1
5. Turn off time vs. ambient temperature characteristics
LED current: 5 mA; Load voltage: 10V (DC); Continuous load current: 80mA (DC)
0.1
6. LED operate current vs. ambient temperature characteristics
Load voltage: Max. (DC); Continuous load current: 80mA (DC)
2 LED operate current, mA
Turn on time, ms
Turn on time, ms
0.08
0.08
1.5
0.06
0.06
1
0.04
0.04
0.5 0.02 0.02
0
-40 -20
0
20
40
60
8085
0
-40 -20
0
20
40
60
8085
0
-40 -20
0
20
40
60
8085
Ambient temperature, C
Ambient temperature, C
Ambient temperature, C
7. LED turn off current vs. ambient temperature characteristics
Load voltage: Max. (DC); Continuous load current: 80mA (DC)
2 LED operate current, mA
8. LED dropout voltage vs. ambient temperature characteristics
LED current: 5 to 50 mA
9. Voltage vs. current characteristics of output at MOS portion
Measured portion: between terminals 3 and 4 Ambient temperature: 25C 77F
Current, mA 50mA 150 100 50
1.5 LED dropout voltage, V
1.4
1.5
1.3 -2 -1.5 -1 -0.5 0.5 -50 -100 -150 1 1.5 2 Voltage, V
1
1.2
0.5
30mA 20mA 10mA 5mA
1.1
0
-40 -20
0
20
40
60
8085
1.0
-40 -20
0
20
40
60
8085 100
Ambient temperature, C
Ambient temperature, C
10. Off state leakage current
Measured portion: between terminals 3 and 4 Ambient temperature: 25C 77F
11. LED forward current vs. turn on time characteristics
Measured portion: between terminals 3 and 4 Load voltage: 10V (DC); Continuous load current: 80mA (DC); Ambient temperature: 25C 77F
0.12
12. LED forward current vs. turn off time characteristics
Measured portion: between terminals 3 and 4 Load voltage: 10V (DC); Continuous load current: 80mA (DC); Ambient temperature: 25C 77F
0.1
Off state leakage current, A
10-3 Turn on time, s 10-5 10-7 10-9 0.03 10-11 10-13 0 0 5 10 15 20 25 30 0 10 20 30 40 50 60 Load voltage, V LED forward current, mA 0.02 0 0 10 20 30 40 50 60 LED forward current, mA Turn off time, s 0.09 0.08
0.06
0.06
0.04
13. Applied voltage vs. output capacitance characteristics
Measured portion: between terminals 3 and 4 Frequency: 1 MHz, 30m Vrms; Ambient temperature: 25C 77F
2.5 Output capacitance, pF
14. Isolation characteristics (50 impedance)
Measured portion: between terminals 3 and 4 Ambient temperature: 25C 77F
100
15. Insertion loss characteristics (50 impedance)
Measured portion: between terminals 3 and 4 Ambient temperature: 25C 77F
2
Insertion loss, dB
2 Isolation, dB
80
1.5
1.5
60
1
1
40
0.5 0.5 20
0
0
5
10
15
20
25
30
04 10
105
106
107
108
0
104
105
106 Frequency, Hz
107
Applied boltage, V
Frequency, Hz
3
AQY221N3V
16. On resistance distribution
Measured portion: between terminals 3 and 4 Continuous load current: 80mA (DC) Quantity, n=60; Ambient temperature: 25C 77F
40 35 40 Quantity, n Quantity, n Quantity, n 0 0.02 0.04 0.06 0.08 0.1 30 25 20 15 10 10 5 0 2 3 4 5 6 7 8 0 10 0
17. Turn on time distribution
Load voltage: 10V (DC) Continuous load current: 80mA (DC) Quantity, n = 60; Ambient temperature: 25C 77F
50
18. Turn off time distribution
Load voltage: 10V (DC) Continuous load current: 80mA (DC) Quantity, n = 60; Ambient temperature: 25C 77F
60 50 40 30 20
30
20
0
0.02
0.04
0.06
0.08
0.1
On resistance,
Turn on time, ms
Turn on time, ms
19. LED operate current distribution
Load voltage: 10V (DC) Continuous load current: 80mA (DC) Quantity, n = 60; Ambient temperature: 25C 77F
30 25 Quantity, n 20 15 10 5 0 0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
LED operate current, mA
DIMENSIONS
mm inch
4.45 .175
Recommended mounting pad (TOP VIEW)
2.65 .104 0.70 .028 0.90 .035
1.27 .050 4.35 .171 1.80 .071 0.20 .008 0.20 .008 0.40 .016 1.27 .050
Tolerance:0.1 .004
(4.85) (.191)
0.40 .016
Terminal thickness = 0.15 .006 General tolerance: 0.1 .004
SCHEMATIC AND WIRING DIAGRAMS
Notes: 1. E1: Power source at input side; IF: LED forward current; VL: Load voltage; IL: Load current Schematic Output configuration
4
Load
Wiring diagram
1
1
4
4
Load
1a
2 3
AC/DC
E1
IF 2 3
IL
VL (AC,DC) 3
IL
VL (AC,DC)
Load
4
AQY221N3V
CAUTIONS FOR USE
1. Short across terminals Do not short circuit between terminals when relay is energized. There is possibility of breaking the internal IC. 2. Surge voltages at the input If reverse surge voltages are present at the input terminals, connect a diode in reverse parallel across the input terminals and keep the reverse voltages below the reverse breakdown voltage. 5. Output spike voltages 1) If an inductive load generates spike voltages which exceed the absolute maximum rating, the spike voltage must be limited. Typical circuits are shown below.
1 4
2 1 2 4 3 1
3
Load
6. Cleaning solvents compatibility Dip cleaning with an organic solvent is recommended for removal of solder flux, dust, etc. Select a cleaning solvent from the following table. If ultrasonic cleaning is used, the severity of factors such as frequency, output power and cleaning solvent selected may cause loose wires and other defects. Make sure these conditions are correct before use. For details, please consult us.
Cleaning solvent Compatibility (: Yes : No)
4
Add a clamp diode to the load
Chlorine base Adueous Alcohol base Others
2
3
Load
3. Recommended LED forward current (IF) It is recommended that the LED forward current (IF) be kept at 5mA. 4. Ripple in the input power supply If ripple is present in the input power supply, observe the following: 1) For LED operate current at Emin, maintain the value mentioned in the table of "3. Recommended LED forward current (IF)." 2) Keep the LED operate current at 50 mA or less at Emax.
Add a CR snubber circuit to the load
* Trichlene * Chloroethlene * Indusco * Hollis * Lonco Terg * IPA * Ethanol * Thinner * Gasoline
2) If spike voltages generated at the load are limited with a clamp diode and the circuit wires are long, spike voltages will occur by inductance. Keep wires as short as possible to minimize inductance.
Emin.
Emax.
7. Soldering When soldering this terminals, the following conditions are recommended. (1) IR (Infrared reflow) soldering method (2) Vapor phase soldering method
T3 T2 T1 T2 T1
(3) Double wave soldering method
T2 T1
t1
t2
t1
t2
t1
t2
t3
T1 = 155 to 165C 311 to 329F T2 = 180C 200C 356 to 392F T3 = 245C 473F or less t1 = 120 s or less t2 = 30 s or less
T1 = 180 to 200C 366 to 392F T2 = 215C 419F or less t1 = 40 s t2 = 40 s or less
T1 = 155 to 165C 311 to 329F T2 = 260C 500F or less t1 = 60 s or less t2+t3 = 5 s or less
(4) Soldering iron method Tip temperature: 280 to 300C 536 to 572F Wattage: 30 to 60 W Soldering time: within 5 s
(5) Others Check mounting conditions before using other soldering methods (hot-air, hot plate, pulse heater, etc.) * The temperature profile indicates the temperature of the soldered terminal on the surface of the PC board. The ambient
temperature may increase excessively. Check the temperature under mounting conditions. * The conditions for the infrared reflow soldering apply when preheating using the VPS method.
5
AQY221N3V
8. The following shows the packaging format 1) Tape and reel
Type Tape dimensions
Tractor feed holes 1.50 +0.5 dia. -0 Direction of picking 1.50 +0.5 dia. -0 3.00.1 4.00.1 1.750.1 .118.004 .157.004 .069.004 5.10.2 .201.008 12.00.3 .472.012 Device mounted on tape 2.70.3 .106.012
+0.1 1.50-0 dia. 5.50.1 +.004 .059-0 dia. .217.004
mm inch Dimensions of paper tape reel
210.8 .827.031 801 dia. 3.150.039 dia. 20.5 .079.020 2502 dia. 9.843.079 dia. 801 dia. 3.150.039 dia.
0.30.05 .012.002
SSOP 4-pin type
4.00.1 .157.004
(1) When picked from 1/4-pin side: Part No. AQYVY (Shown above) (2) When picked from 2/3-pin side: Part No. AQYVW
130.5 dia. .512.020 dia. 141.5 .551.059
20.5 .079.020
2) Storage PhotoMOS relays implemented in SSOP types are sensitive to moisture and come in sealed moisture-proof packages. Observe the following cautions on storage. * After the moisture-proof package is unsealed, take the devices out of storage as soon as possible (within 1 month at the most). * If the devices are to be left in storage for a considerable period after the moistureproof package has been unsealed, it is recommended to keep them in another moisture-proof bag containing silica gel (within 3 months at the most). 9. Transportation and storage 1) Extreme vibration during transport will warp the lead or damage the relay. Handle the outer and inner boxes with care. 2) Storage under extreme conditions will cause soldering degradation, external appearance defects, and deterioration of the characteristics. The following storage conditions are recommended: * Temperature: 0 to 45C 32 to 113F * Humidity: Less than 70% R.H. * Atomosphere: No harmful gasses such as sulfurous acid gas, minimal dust.
10. Applying stress that exceeds the absolute maximum rating If the voltage or current value for any of the terminals exceeds the absolute maximum rating, internal elements will deteriorate because of the excessive voltage or current. In extreme cases, wiring may melt, or silicon P/N junctions may be destroyed. As a result, the design should ensure that the absolute maximum ratings will never be exceeded, even momentarily. (Use at 15 V DC or lower and 9 V DC or lower is recommended.) 11. Deterioration and destruction caused by discharge of static electricity This phenomenon is generally called static electricity destruction. This occurs when static electricity generated by various factors is discharged while the relay terminals are in contact. The result can producing internal destruction of the element. To prevent problems from static electricity, the following precautions and measures should be taken when using your device. 1) Employees handling relays should wear anti-static clothing and should be grounded through protective resistance of 500 k to 1 M.
2) A conductive metal sheet should be placed over the work table. Measuring instruments and jigs should be grounded. 3) When using soldering irons, either use irons with low leakage current, or ground the tip of the soldering iron. (Use of lowvoltage soldering irons is also recommended.) 4) Devices and equipment used in assembly should also be grounded. 5) When packing printed circuit boards and equipment, avoid using high-polymer materials such as foam styrene, plastic, and other materials which carry an electrostatic charge. 6) When storing or transporting relays, the environment should not be conducive to generating static electricity (for instance, the humidity should be between 45 and 60%). Relays should always be protected using non-conductive packing materials.
These materials are printed on ECF pulp. These materials are printed with earth-friendly vegetable-based (soybean oil) ink.
Please contact ..........
Matsushita Electric Works, Ltd.
Automation Controls Company Head Office: 1048, Kadoma, Kadoma-shi, Osaka 571-8686, Japan Telephone: Japan (81) Osaka (06) 6908-1050 Facsimile: Japan (81) Osaka (06) 6908-5781 http://www.nais-e.com/ COPYRIGHT (c) 2003 All Rights Reserved
ASCT1B268E 6 200303 Specifications are subject to change without notice. Printed in Japan.

▲Up To Search▲

Price & Availability of AQY221N3V

	To Download AQY221N3V Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .